Oki Pos 441 Manual do Utilizador

User’s Guide59307701OkiPos 441

– 6 –4. Setup4-1. Connecting the Cable to the PC4-1-1. Parallel Interface CableConnect the parallel interface cable to a parallel port of your PC.4-1

– 7 –4-2. Connecting the Cable to the PrinterNote that the interface cable is not provided. Please use a cable that meets specifications.CAUTIONBefore

– 8 –4-2-2. RS-232 Interface Cable(1) Make sure the printer is turn off.CAUTIONBefore connecting/disconnecting the interface cable, make sure that po

– 9 –4-2-4. Connecting Ethernet Cable(1) Make sure the printer is turned off.(2) Affix the ferrite core onto the ethernet cable as shown in the illus

– 10 –4-3. Installing the Printer SoftwareHere is the procedure for installing the printer driver and utility software, which are stored on the suppl

– 11 –4-4. Connecting to a Peripheral UnitYou can connect a peripheral unit to the printer using a modular plug. See “Modular plug” on page 33 for de

– 12 –4-5. Connecting the Power CordNote: Before connecting/disconnecting the power cord, make sure that power to the printer and all the devices con

– 13 –4-6. Turning Power OnMake sure that the Power cord has been connected as described in 4-5.Turn ON the power switch located on the front of the

– 14 –4-7. Installing the CableInstall the cable as shown in the diagram below.4-8. Switch Blind InstallationIt is not necessary to install the swit

– 15 –5. Loading the Ribbon Cartridge and PaperFinger gripFinger grip5-1. Loading the Ribbon Cartridge1 Turn off power to the printer.2 Open the fr

Federal Communications CommissionRadio Frequency InterferenceStatementThis equipment has been tested and found to comply with the limits for a Class A

– 16 –5-2. Loading the paper1 Open the printer cover by sliding the latch toward you.Important!1. Do not touch the print head immediately aft

– 17 –4 Tear Bar Model: Tear off the paper as shown. Auto Cutter Model: If the printer cover is closed after turning on the power, the cutter oper

– 18 –5-3. Installing the Roll Paper GuideWhen using paper roll with 57.5 mm or 69.5 mm width, install the attached roll paper guide in the groove in

– 19 –Caution Symbol This symbol is placed near the print head to indicate that it may be hot. Never touch the print head immediately after the pri

– 20 –CAUTION3 We recommend that you unplug the printer from the power outlet whenever you do not plan to use it for long periods. Because of this, yo

– 21 –6. Control Panel and Other Functions6-1. Control Panel2 FEED button3 ERROR lamp (Red LED)1 POWER lamp (Green LED)1 POWER lamp (Green LED) Light

– 22 –6-3. Errors1) Recoverable errorError Descrip-tionPOWER lamp ERROR lampBuzzer Recovery ConditionsPaper end error OnFlashes (On: 1 sec./Off: 1 s

– 23 –*7 Automatically the printer is recovered if the cutter returns to the home position after turn-ing the power OFF and ON. Restoration is also

– 24 –6-4. Adjustment ModeThere are the following seven adjustment modes.The device will enter the adjustment mode if your turn it on while pressing

– 25 –6-4-1. Self Printing ModeSelf-printing will be performed to print the Ver. No. and printer settings. ASCII-printing will be repeated when the F

TABLE OF CONTENTS1. Outline ...

– 26 –or like this6-4-2. Adjusting the Dot Alignment ModeYou may never have to use the procedure described in this section, but after you have been us

– 27 –(3) To adjust, use the FEED switch to select the adjustment pattern from the printout with the smallest gap between the first printing pass and

– 28 –6-4-3. Hexadecimal Dump ModeEach of the signals sent from the computer to the printer will be printed out in hexadecimal code.This function allo

– 29 –6-4-4. Black Mark Sensor Alignment Mode1. Turn the printer off and unplug the power cord.2. Place the printer upright as shown below to remove

– 30 –7. Preventing and Clearing Paper Jams7-1. Preventing Paper JamsThe paper should not be touched during ejection and before it is cut.Pressing or

– 31 –7-3. Releasing a Locked Cutter (Auto Cutter Mode only)If the auto cutter locks up or fails to cut the paper, follow the steps below.WARNINGSinc

– 32 –(6) After you have opened the printer cover, remove the four screws to remove the printer cover and reveal the cutter.(7) If the cutter is loc

– 33 –Modular plugPin No.Signal nameFunction I/O direction1 FG Frame ground —2 DRD1 Drive signal 1 OUT3 +24V Drive power OUT4 +24V Drive power OUT5 D

– 34 –Notes: 1. Peripheral units 1 and 2 cannot be driven simultaneously. To drive them continu-ously, set the duty cycle ratio to 20% or less (exclu

– 35 –9. General Specications9-1. General SpecificationsPrinting method: Serial impact dot matrixPrint direction: Bi-directionalNumber of head pins

13. USB, Ethernet and Wireless LAN Interface ...5013-1. USB Interfa

– 36 – Ribbon material: Nylon 66 (#40 denier) Ribbon life: 441Ribbon Black/Red: Black 1,500,000 characters/Red 750,000 characters 441Ribbon Bla

– 37 –9-2. Power Supply SpecificationsPower Supply: Input: 100 to 240V AC, 50/60HzConsumption Current: Conditions: Excluding perpheral unit drivi

– 38 –10. Dip Switch SettingA DIP switch is provided at the bottom of the printer, and can be set as given in the table be-low. Be sure to set the pow

– 39 –n DIP switchSW No. Function ON OFF1-1Always ON Should be set on1-2 Auto Cutter *1Invalid Valid1-3Always ON Should be set on1-4Command emulation

– 40 –10-1. RS-232C Interface ModelThe RS-232C interface model is equipped with DIP switches on the serial interface board unit to change the communic

– 41 –10-2. Parallel Interface ModelThe parallel interface model is equipped with the main DIP switch only.10-3. USB Interface ModelThe USB interface

– 42 –10-5. Wireless LAN Interface ModelDIP-SW 2Switch ON OFF2-1Fixed at OFF2-2Initialize of setting information —Change DIP Switch 2-2 to ON to initi

– 43 –* This product contains Transmitter Module which conforms to the R&TTE Directive.* This product contains Transmitter Module FCC ID: M4B618

– 44 –Connecting the peripheral drive cableConnect the peripheral drive cable to the connector on the printer. Then, connect the other end of the cabl

– 45 –11. RS-232C Serial InterfaceMARK “1”A: Start bitB: Data bitC: Parity bitD: Stop bit11-1. Interface Specifications1 Data transmission method: As

– 1 –1. OutlineOKIPOS441 Series Serial Impact Dot Matrix Printer is designed for use with electronic instru-ments such as POS, banking equipment, comp

– 46 –11-2. Pins and Signal NamesPin No. Signal Name Direction Function1 FG — Frame ground2 TXD OUT Transmission data3 RXD IN Receive data4 RTS OUT Al

– 47 –Pin No. Signal Name Direction Function20DTR OUT X-On/X-Off Communication ModeAlways space, except during following conditions:• Period between r

– 48 –12. Parallel InterfaceThe two-way parallel interface is compatible with the IEEE1284 compatibility mode and nib-ble mode.12-1. Table of Connecti

– 49 –Pin No. DirectionCompatibility Mode Signal NameNibble Mode Signal Name31 In nInit nInit32 Out nFault nDataAvail/Data0,433 EXT GND —34Out Compu

– 50 –13. USB, Ethernet and Wireless LAN Interface13-1. USB Interface Specifications1. General Specification: Conforms to USB 2.0 Specifications2. Com

– 51 –14. Memory Switch SettingsEach memory switch is stored in EEPROM. For details on the functions and settings of memory switches, see the separate

Oki Data Americas, Inc., 2000 Bishops Gate Blvd., Mt.Laurel, NJ 08054-4620Tel: 1-800-Oki-Data (1-800-654-3282) Fax: (856) 222-5320 www.okiprintingso

– 2 –2. Unpacking and Installation2-1. UnpackingAfter unpacking the unit, check that all the necessary accessories are included in the package.Note:

– 3 –2-2. Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes to think about where you plan to use i

– 4 –2-3. Handling Care1. Be careful not to drop paper clips, pins or other foreign matter into the unit as these cause the printer to malfunction.2

– 5 –3. Parts Identication and NomenclaturePrinter coverProtects the printer from dust and reduces noise.Do not open the cover while printing.Control