Oki RT322POS Manual do Utilizador

User’s Guidemoc.atadiko.ym59102601RT322OKIPOS 408II

– 6 –3-2-2. RS-232C Interface Cable(1) Make sure the printer is turn off.CAUTIONBefore connecting/disconnecting the interface cable, make sure that p

– 7 –(1) Make sure the printer is turned off.(2) Install the ferrite core onto the ethernet cable as shown in the illustration below.(3) Pass the f

– 8 –3-3. Installing the Printer SoftwareHere is the procedure for installing the printer driver and utility software, which are stored on the suppli

– 9 –3-4. Connecting the Optional AC AdapterNote: Before connecting/disconnecting the AC adapter, make sure that power to the printer and all the dev

– 10 –3-5. Turning Power OnMake sure that the Power cord has been connected as described in 3-4.Turn ON the power switch located on the front of the

– 11 –3-6. Connecting to a Peripheral UnitYou can connect a peripheral unit to the printer using a modular plug. See “Modular plug” on page 53 for de

– 12 –3-7. Loading the Paper RollBe sure to use paper roll that matches the printer’s specication.Cover open leverPaper rollTension barカバーオープンレバー

– 13 –3-7-1. Removing the Tension BarWhen using thermal paper roll, the tension bar unit may or may not be necessary, depending on the paper thickness

– 14 –3-7-2. Removing the Paper Roll HolderWhen using a paper roll with an 79.5 mm width, install the paper roll holder into the groover as shown. And

– 15 –WARNING1) Do not touch the cutter blade. • There is a cutter inside the paper outlet slot. Not only should you not put your hand in the paper

Federal Communications CommissionRadio Frequency InterferenceStatementThis device complies with Part 15 of the FCC Rules. Operation is subject to the

– 16 –9) A printed piece of thermal paper may become electrically charged. If the printer is placed vertically or mounted on a wall, the cut piece of

– 17 –4. Consumable Parts and AC AdapterWhen consumable parts have run out, use those specied in the table below. Make sure that the AC adapter speci

– 18 –Manufacture Product name Quality characteristics/Use Paper thickness(µm)Oji Paper Co., Ltd. PD150R normal type paper 75PD160R high image stabili

– 19 –4-2. Thermal Label Paper Roll (Tack Label Paper)(1) Label paper specication Backing paper width: 110±0.5 mm Outer roll diameter: ø100 mm

– 20 –ø100 MAX110 +1.5-1.0(Rolled dimension)ø32 ± 1ø25.4 ± 11 +1.0-0.815 MIN(2.5)105 ± 0.5 (Label width)110 ± 0.5 (Backing paper width)2.5 ± 0.55 ±

– 21 –• Cut Position / Printing Line / Black Mark Sensor’s Positional Relationship4-3. AC adapter (option)AC adapter which are not specied may resu

– 22 –5. Control Panel and Other Functions5-1. Control Panel POWER lamp (Green LED) When the printer is online, power lamp is ON and ERROR lamp is

– 23 –2) Non-recoverable errorsError Description POWER Lamp ERROR LampRecovery ConditionsFlash access error OFF Flashes Orange lamp at 0.5-sec-ond in

– 24 –5-3. Self-Printing5-3-1. Test PrintingPlace the thermal paper roll on the printer.Turn the power ON while holding the FEED button depressed. The

– 25 –6. Adjusting the SensorThis printer is equipped with the following two paper sensors:• PE and BM (Paper End and Black Mark) Sensor Detects whe

TABLE OF CONTENTS1. Unpacking and Installation ...

– 26 –Adjustment value according to the paper you are usingPaper thickness (µm)When using the paper roll with a core whose inside diameter (A):ø12, ou

– 27 –OFFON1 2 3 4 5 6 7 8 1 2 3 4DSW 2 DSW 1VR 1VR 3109VR 2Paper rollERRORFEEDPOWERPower switchPower lampERROR lamp6-2. PE and BM ( Paper End and Bl

– 28 –OFFON1 2 3 4 5 6 7 8 1 2 3 4DSW 2 DSW 1VR 1VR 3109VR 2ERRORFEEDPOWERPower switchPower lampERROR lampPaper roll6-3. NE (Near End) Sensor Adjustm

– 29 –7. Preventing and Clearing Paper Jams7-1. Preventing Paper JamsThe paper should not be touched during ejection and before it is cut.Pressing or

– 30 –8. Periodical CleaningPrinted characters may become partially unclear due to accumulated paper dust and dirt. To prevent such a problem, paper d

– 31 –9. Specications9-1. General Specications(1) Printing method Direct line thermal printing(2) Print speed Max. 1440 dots/sec. (180 mm/sec.)(

– 32 –9-2. Auto Cutter Specications(1) Cutting frequency Max. 20 cuts per minute(2) Thickness of paper 0.065 ~ 0.15 mm (when using 115.5 mm widt

– 33 –9-5. Environmental Requirements(1) Operating Temperature 41°F to 113°F (5°C to 45°C) Humidity 10% to 90% RH (without condensation)(2) Tra

– 34 –9-6. Reliability Specications(1) Life Mechanical: 20 million lines Print Head: 150 km (150 million pulses ) Auto Cutter: 2 million

– 35 –9-7. Black mark specications<Remarks>1) The cut position shown above is when the print starting position correct value for Section 15:

12. RS-232C Serial Interface ... 481

– 36 –10. Dip Switch SettingTwo DIP switches are provided at the bottom of the printer, and can be set as given in the table below. Be sure to set the

– 37 –10-1. Parallel Interface Model ON ON OFF OFF DIP-SW 1Switch 1-1 Switch 1-2 Command emulationON ON Star Line ModeOFF ON Star Page ModeON OFF

– 38 –(3) ESC/POS modeSwitch Function ON OFF1-1 Command emulation Always OFF1-2 Command emulation Always OFF1-3 Should not be changed (Should be set

– 39 –No. 1 2 3 4 5 6 7 8 No. 1 2 3 49 10DIP-SW 1 DIP-SW 210-2. RS-232C Interface Model ON ON OFF OFF DIP-SW 1Switch 1-1 Switch 1-2 Command emula

– 40 –(3) ESC/POS modeSwitch Function ON OFF1-1 Command emulation Always OFF1-2 Command emulation Always OFF1-3 Should not be changed (Should be set

– 41 –The following is the procedure for changing the settings on DIP switch No. 3.1. Turn off the printer and all components connected to it.2. Rem

– 42 –No. 1 2 3 4 5 6 7 8 No. 1 2 3 49 10DIP-SW 1 DIP-SW 210-3. USB Interface Model ON ON OFF OFF DIP-SW 1Switch 1-1 Switch 1-2 Command emulation

– 43 –2) Star Page ModeSwitch Function ON OFF1-1 Command emulation Always OFF1-2 Command emulation Always ON1-3 Should not be changed (Should be set

– 44 –No. 1 2 3 4 5 6 7 8 No. 1 2 3 49 10DIP-SW 1 DIP-SW 210-4. EthernetInterface Model ON ON OFF OFF DIP-SW 1Switch 1-1 Switch 1-2 Command emula

– 45 –(3) ESC/POS modeSwitch Function ON OFF1-1 Command emulation Always OFF1-2 Command emulation Always OFF1-3 Should not be changed (Should be set

– 1 –1. Unpacking and Installation1-1. UnpackingAfter unpacking the unit, check that all the necessary accessories are included in the package.Note: T

– 46 – Initializing SettingsSet the push switch as described below to initialize the setting information.Push the switch for one to ve seconds whil

– 47 –11. Parallel InterfaceThe two-way parallel interface is compatible with the IEEE1284 compatibility mode and nibble mode. Refer to the separate S

– 48 –A: Start bitB: Data bitC: Parity bitD: Stop bitA B C Db0 b1 b2 b3 b4 b5 b6 (b7)12. RS-232C Serial Interface12-1. Interface Specications Data

– 49 –12-2. RS-232C ConnectorPin No. Signal name Direction Function1 F-GND — Frame ground2 TXD OUT Transmission data3 RXD IN Receive data4 RTS OUT S

– 50 –1325114D-sub 25 PinPin No. Signal name Direction Function20 DTR OUT2) ESC/POS ModeA) DTR communication modeIndicates whether data receive from

– 51 –12-3. Cable ConnectionsThe followings are a recommended interface cable connections.Note: Use shielded wire less than 3 m in length.12-4. Electr

– 52 –13. USB and Ethernet Interface13-1. USB Interface Specications1. General Specication: Conforms to USB 2.0 Specications2. Communication Spe

– 53 –Modular plugPin No.Signal nameFunction I/O direction1 FG Frame ground —2 DRD1 Drive signal 1 OUT3 +24 V Drive power OUT4 +24 V Drive power OUT5

– 54 –Note:1) Peripheral units 1 and 2 cannot be driven simultaneously.2) To drive them continuously, set the duty cycle ratio to 20% or less (excep

– 55 –15. Memory Switch SettingsEach memory switch is stored in EEPROM. For details on the functions and settings of memory switches, refer to the sep

– 2 –1-2. Choosing a place for the printerBefore actually unpacking the printer, you should take a few minutes to think about where you plan to use i

59102601

– 3 –2. Parts Identication and NomenclatureInterface connectorFor connection to a host computer.Peripheral drive connectorConnects to peripheral unit

– 4 –3. Setup3-1. Connecting the Cable to the PC3-1-1. Parallel Interface CableConnect the parallel interface cable to a parallel port of your PC.3-1

– 5 –3-2. Connecting the Cable to the PrinterNote that the interface cable is not provided. Please use a cable that meets specications.CAUTIONBefore